G Touch G3 Firmware Stock Rom/Flash FIle Download
>>On this post you will find G Touch G3 Firmware Stock Rom/Flash FIle Download 100% Tested V08/V01 Read With CM2 By GSM_Abinash. This File Is pin,password,pattern,bootloop,hang on logo,dead recover fix,FRP remove 100% tested G Touch G3 Firmware Stock Rom/Flash FIle Download V08/V01 And Enjoy!!!
#About Phone G Touch G3 ?
1. Device Brand : MITO
2. Device Model : MITO-A880
3. Device CPU : sp7731cea
4. Device IntName : MITO A880
5. Device Version : 6.0
6. Device Compile : 12/6/2017 1:01:11 PM
7. Device Project : MITO_A880_06122017_V08
8. Device ExtInfo : MITO A880
9. File Size : 539.51MB
10. File Type : Password Protect
11. Password : 3$
#G Touch G3 Firmware Stock Rom/Flash FIle Features ?
1. Pin Remove.
2. Pattern Remove.
3. Password Remove.
4. Hang On Logo Problem Solve.
5. Boot Logo Promlem Solve.
6. Dead Fix Solved.
7. FRP Remove.
#G Touch G3 Firmware Stock Rom/Flash FIle Reading ?
Card found: S/N : 3C1C16EE , v0137
Chinese Miracle II [SPD module] v 1.27
Set mode to : SP [SC773x] eMMC [Android 6.x]
Operation : Check/Read Info [ v1.27 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
-> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable
==== Wait for phone...
Phone found! [ 108 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FLASH : eMMC Flash , Structure : Ok!
Reading extended info ...
Model Name : MITO A880
Model Brand : MITO
Model Device: MITO-A880
AndrVersion : 6.0
BaseBand CPU: SP7731CEA
CompileDate : 12/6/2017 1:01:11 PM
Project Ver : MITO_A880_06122017_V08
Model Ext : MITO A880
ExtraInfo : HWInfo not exists, normal phone
Elapsed: 00:00:29
Reconnect Power/Cable!
Operation : Read FullFlash [ v1.27 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
-> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable
==== Wait for phone...
Phone found! [ 108 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!
[FW_READER] : Prepare Ok!
- > Wait phone connected ...
Phone found! [ 108 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
- > Wait phone connected ...
Phone found! [ 108 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Model Name : MITO A880
Model Brand : MITO
Model Device: MITO-A880
AndrVersion : 6.0
BaseBand CPU: SP7731CEA
Project Ver : MITO_A880_06122017_V08
Model Ext : MITO A880
[Read Mode] : HSUSB : 0x3000
[FW_READER] : Reading Firmware Now ...
[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : sc7731C_CP0_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : nvitem_w.bin
[Read Ok] : sc8830g_modem_CP2_WCN_Trunk_W17.27.4_Release.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : logo_540x960.bin
[Read Ok] : fblogo_480x854.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Read Ok] : sysinfo.img
[Build Ok] : cache.img
[Read Ok] : recovery.img
[Build Ok] : userdata.img
AndroidInfo created
Firmware Size : 1877 MiB
Saved to : C:\Users\GSM-Abinash\Desktop\New folder\SP7731CEA_MITO-A880_6.0_MITO_A880_06122017_V08_MITO_A880\
Done!
Elapsed: 00:13:48
Reconnect Power/Cable!
#How To Flash G Touch G3 Firmware Stock Rom/Flash FIle Update ?
>>-:Follow Guide : Click Here
#G Touch G3 Firmware Stock Rom/Flash FIle link ?
>>-:MediaFire : Click Here
#G Touch G3 FRP Remove Done With CM2 SPD Model SC7731X ?
Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
-> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable
==== Wait for phone...
Phone found! [ 108 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!
eMMC phone detected! Will use 'Safe Format' mode!
Mount : /data
Size : 0x0000000063EF7000
State : 0x0001
Mount : /cache
Size : 0x000000000FA00000
State : 0x0001
Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!
Android 5.x/6.x : Reset FRP Lock
Reset Ok!
Done!
Elapsed: 00:00:26
Reconnect Power/Cable!
#About Phone G Touch G3 ?
1. Device Brand : MITO
2. Device Model : MITO-A880
3. Device CPU : sp7731cea
4. Device IntName : MITO A880
5. Device Version : 6.0
6. Device Compile : 12/6/2017 1:01:11 PM
7. Device Project : MITO_A880_06122017_V08
8. Device ExtInfo : MITO A880
9. File Size : 539.51MB
10. File Type : Password Protect
11. Password : 3$
#G Touch G3 Firmware Stock Rom/Flash FIle Features ?
1. Pin Remove.
2. Pattern Remove.
3. Password Remove.
4. Hang On Logo Problem Solve.
5. Boot Logo Promlem Solve.
6. Dead Fix Solved.
7. FRP Remove.
#G Touch G3 Firmware Stock Rom/Flash FIle Reading ?
Card found: S/N : 3C1C16EE , v0137
Chinese Miracle II [SPD module] v 1.27
Set mode to : SP [SC773x] eMMC [Android 6.x]
Operation : Check/Read Info [ v1.27 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
-> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable
==== Wait for phone...
Phone found! [ 108 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FLASH : eMMC Flash , Structure : Ok!
Reading extended info ...
Model Name : MITO A880
Model Brand : MITO
Model Device: MITO-A880
AndrVersion : 6.0
BaseBand CPU: SP7731CEA
CompileDate : 12/6/2017 1:01:11 PM
Project Ver : MITO_A880_06122017_V08
Model Ext : MITO A880
ExtraInfo : HWInfo not exists, normal phone
Elapsed: 00:00:29
Reconnect Power/Cable!
Operation : Read FullFlash [ v1.27 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
-> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable
==== Wait for phone...
Phone found! [ 108 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!
[FW_READER] : Prepare Ok!
- > Wait phone connected ...
Phone found! [ 108 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
- > Wait phone connected ...
Phone found! [ 108 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Model Name : MITO A880
Model Brand : MITO
Model Device: MITO-A880
AndrVersion : 6.0
BaseBand CPU: SP7731CEA
Project Ver : MITO_A880_06122017_V08
Model Ext : MITO A880
[Read Mode] : HSUSB : 0x3000
[FW_READER] : Reading Firmware Now ...
[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : sc7731C_CP0_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : nvitem_w.bin
[Read Ok] : sc8830g_modem_CP2_WCN_Trunk_W17.27.4_Release.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : logo_540x960.bin
[Read Ok] : fblogo_480x854.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Read Ok] : sysinfo.img
[Build Ok] : cache.img
[Read Ok] : recovery.img
[Build Ok] : userdata.img
AndroidInfo created
Firmware Size : 1877 MiB
Saved to : C:\Users\GSM-Abinash\Desktop\New folder\SP7731CEA_MITO-A880_6.0_MITO_A880_06122017_V08_MITO_A880\
Done!
Elapsed: 00:13:48
Reconnect Power/Cable!
#How To Flash G Touch G3 Firmware Stock Rom/Flash FIle Update ?
>>-:Follow Guide : Click Here
#G Touch G3 Firmware Stock Rom/Flash FIle link ?
>>-:MediaFire : Click Here
NOTE: If You Have Any Problems Then Comment Below Or Message Us, We Try Our Best To Help You. If You Found This Post Helpful Then Don't Forgot To Like And Share.
#G Touch G3 FRP Remove Done With CM2 SPD Model SC7731X ?
Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
-> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable
==== Wait for phone...
Phone found! [ 108 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!
eMMC phone detected! Will use 'Safe Format' mode!
Mount : /data
Size : 0x0000000063EF7000
State : 0x0001
Mount : /cache
Size : 0x000000000FA00000
State : 0x0001
Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!
Android 5.x/6.x : Reset FRP Lock
Reset Ok!
Done!
Elapsed: 00:00:26
Reconnect Power/Cable!
Post a Comment